Suzuki SDT-2 works with Ford VCM II clone

Is it possible to use a VCM 2 unit for Suzuki diagnosis with SDT 2?

Yes!

The basic steps
– install IDS software in clean VM Windows 7 32 bit.
– downgrade firmware to v2.1.119.19
-Mazda-V94
– install SDT SDT-II_soft_2140025
– in C:\Program Files\Bosch\VTX-VCI copy all files from “VCI Software (Ford-VCM-II)” to “VCI Software (6516-Suzuki)”
and run.

In detail…

For owners of Ford VCM II (dual-board), an instruction (more specifically a review) for installing and configuring the Ford VCM II to work with the Suzuki SDT-2 program.

The site of the program is posted (sold) version 2.8.0.46, on the network (thanks to the distributor) 2.9.0.47 (from 1.10.2015).

For those already using the Ford VCM II with the Ford IDS program.

On the laptop (or OS) where the Ford VCM II with Ford IDS is installed and running, go along the path:

C: \ Program Files \ Ford Motor Company \ IDS \ Runtime \ install3rdparty \ ETAS
or
C: \ Program Files (x86) \ Ford Motor Company \ IDS \ Runtime \ install3rdparty \ ETAS
Regards … (Thanks to vagvag for the information).

Copy and save in a convenient place for you or media, the file is the installer of the VCM II manager running Ford IDS.

Install the Suzuki SDT-2. Run the installer program, after a short time the program will ask you to connect VCM II. It is enough to connect via USB. We connect, only after this the program will be completely installed. (VCM II connected)

The program is installed, turn off VCM II.

We launch the file of the installer of the Ford VCM 2 manager running Ford IDS.

We follow the path: “C: \ Program Files \ VTX-VCI”. We see two folders of VCI Software (6516-Suzuki) and VCI Software (Ford-VCM-II).

We copy the contents of the VCI Software folder (Ford-VCM-II) and paste it into the VCI Software folder (6516-Suzuki).

Reboot. We plug the power of 12 volts through the diagnostic tool, the VCM II is plugged, we connect the VCM II via USB to the laptop. There will be, as usual, installation of drivers.

Launch the VCM II Manager. The Start button \ All Programs \ Bosch \ VCI Software (6516-Suzuki) \ VCM Manager (6516-Suzuki). Click Connect. A green quote appears in the VCM image. Click on Show Details. Look, in the lines of the PC S / W Version and VCM II S / W Version, the numbers match. At the top of the picture VCM Manager inscription VCM II Manager (Ford-VCM-II). It should be so. We close VCM Manager.

We launch Suzuki SDT-2. We rejoice.

When working with the program. Connected the scanner to the car, waited for “peak”, connected via USB to the laptop and run Suzuki SDT-2. If necessary, we switch to the required language via the System Configuration (Russian is present). I have an eng OS and the program was installed with a sample of English. We are working. The program is simple, I think the questions should not arise.

Good luck!

Type 3

Type 4

Liana

Alivio

Baleno 96-01

Grand Vitara

Wagon R

Jimny

Ignis

RIZT 07-15

BREZZA

Select from type

Type 1

Type 2

Type 3

Type 4

Type 5

Type 6

Type 7

Type 8

Type 9

Type 10

Type 11

Type 12

Smart key system

Alivio

S-CROSS

Vitra

Suzuki odometer correction: Obdstar F109

Grand Vitara

Type 1 D70F3421

Type 2 D70F3422

Kizashi D70F3422