4 Steps to Program VW CC 2014 Key by Xtool X-100 PAD2 Pro

XTOOL X100 PAD 2 Pro full version adds VW 4th & 5th IMMO. This post comes with the guide to use it to add new key to VW CC 2014 by PIN code.

Preparation:

Xtool X-100 PAD2 Pro full Configuration (€813.64 free shipping from UK)

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-1

This is comfort control module EEPROM chip of VW CC 2014

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-2

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-3

Reading EEPROM chip

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-4

Prepare two keys: Original one+ blank one

Test two key first

The original key can remote and start the car

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-5

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-6

The blank key cannot work

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-7

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-8

Main 4 steps to program key:

Step 1: Get pin code

Step 2: Generate 48 dealer key

Step 3: Match new key

Step 4: Program remote

In detail…

Step 1: Get pin code

Connect X100 PAD2 PRO with KC100 to the vehicle

Insert the original key into ignition

Press X100 PAD2 on the device

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-9

Select Immobilization-> VW-> 4th& 5th Immobilizer system、

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-10

Turn on ignition switch

Select 4th immobilizer system-> VW Passat/CC (Recommend) -> Get PIN/CS

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-11

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-12

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-13

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-14

Follow the prompt to select EEPROM data

Codes will be extracted from EEPROM chip dump file

Step 2: Generate 48 dealer key

Select Generate 48 dealers key to activate KC100 adapter

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-15

Then input CS code

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-16

Put the blank key to coil

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-17

Generate 48 dealer key successfully

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-18

Step 3: Match new key

Select Match the key

Enter Pin code and learning key number

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-19

Enter the learning mode after confirm immo, use each matched key to turn on ignition switch

Match new key succeed

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-20

The original key and new key both can start the car, but the new key cannot remote

Step 4: Program remote

Select Program remote

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-21

Turn on ignition switch

Select 46 Central comfort module (CANBUS) -> Erase remote

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-22

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-23

Erase remote success

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-24

Then select Program remote

Press any key of the remote to add once program completed

Xtool-X100-Pad2-Pro-Program-Vw-Cc-2014-25

Finally, the new key is working.

Be the first to comment

Leave a Reply

Your email address will not be published.


*